DiagBox Firmware: Appli 8.3.5 + BT 1.2.4

Simple · 20/07/2017, 13h00

The software provided is intended for personal, educational and experimental use; to help with DiagBox installations and XS Evolution VCI communication. I hold no responsibility for any illegal or improper usage or any damage to your system. Carry out upgrade at your own risk.

For those interested in experimenting with the different DiagBox firmware versions, I have attached the latest (to-date) Application (Appli.com 4.3.5, DiagBox v8.45) and Blue Tooth (1.2.4, DiagBox v8.43) Firmware.

I have also included the older BT firmware (1.2.3, DiagBox v8.30) as it includes the HEX file, in case someone needs it.

Simple..

Simple · 24/07/2017, 15h45

The are 2 ways of up****** XS Evolution VCI Firmware,

1- Automatic up******, Follow instructions in this link:
http://www.tlemcen-electronic.com/fo...560#post540560

2- Manual up******, download and install "PSA Interface Checker Install.exe",
a- Ensure XS Evolution VCI is connected and recognised
b- Click on Activate, greyed buttons will become active
c- Click Version to check current version
d- Click Select file to choose the Firmware file desired for upgrade
e- Click Downloading to start the flashing process.

Please wait 5 seconds after the flashing process finished and before disconnecting or starting other application, to ensure no flashing corruption.

djslowrnb · 26/09/2017, 12h06

Thanks simple i use version 7.83 how to know the good firmware fot this version depend car to dagnostic?
thanks!!!

Simple · 26/09/2017, 21h53

DiagBox from version 7.66/8.02 to 8.44 has 4.3.4, but users have used other versions successfully.

djslowrnb · 26/09/2017, 22h17

Citation:

Envoyé par Simple

DiagBox from version 7.66/8.02 to 8.44 has 4.3.4, but users have used other versions successfully.

Thanks Simple, you Maitresox et Scary we are the best !!!!

djslowrnb · 27/09/2017, 21h15

Citation:

Envoyé par Simple

DiagBox from version 7.66/8.02 to 8.44 has 4.3.4, but users have used other versions successfully.

Thanks you is the best!!!

djslowrnb · 01/10/2017, 20h20

Citation:

Envoyé par Simple

DiagBox from version 7.66/8.02 to 8.44 has 4.3.4, but users have used other versions successfully.

Hello simple

I have problem to dialog with my car 308 year 2008
VCI sporadig not read VIN and not read units
I test with many version firmware and result is the same my vci is not good?
But with old 6.16 i not have this problem...
Nlc have flash my unit in 2014

Simple · 01/10/2017, 20h28

Was the VCI working with the same 308? Try using your VCI with another Peugeot or Citroen car and see if it detects it. Is the Windows Driver installing and working OK?

Some VCI's have a problem with C5 and 207/208. More experienced forum members may be able to help!!

djslowrnb · 02/10/2017, 00h07

thanks for response Simple!!
I have problem when i read vin, the read fonction at random the diagnostic is not good....
i see the message connect vci....
I try to update other firmware and one time i see peripheric is not reconize but now its ok i daed my VCI?probably?

regards !!

Discussions similaires
Discussion	Auteur	Forum	Réponses	Dernier message
OPCOM Firmware 1.70	djrusskof	Opcom, Tech2	21	19/02/2019 16h36
appli smarthphone pour decoder poste renault	diagologie	Autoradio et Navigateur GPS	4	04/09/2016 15h30
recherche firmware aPPLI 4.3.3 et 4.3.4	jasmin	LEXIA, PP2000, DiagBox	15	07/05/2015 09h25
Update diagbox 7.40 et firmware 4.3.2	CED300482	LEXIA, PP2000, DiagBox	8	23/04/2014 21h57
demande d'appli	antvan	Probleme des membres	1	13/01/2014 10h02

24/07/2017, 15h45	#2
Simple Membre attaché Date d'inscription: août 2014 Localisation: NA Messages: 279 Thanks: 5 Thanked 414 Times in 80 Posts Pouvoir de réputation: 20	The are 2 ways of up**** XS Evolution VCI Firmware, 1- Automatic up**, Follow instructions in this link: http://www.tlemcen-electronic.com/fo...560#post540560 2- Manual up****, download and install "PSA Interface Checker Install.exe", a- Ensure XS Evolution VCI is connected and recognised b- Click on Activate, greyed buttons will become active c- Click Version to check current version d- Click Select file to choose the Firmware file desired for upgrade e- Click Downloading to start the flashing process. Please wait 5 seconds after the flashing process finished and before disconnecting or starting other application, to ensure no flashing corruption.

26/09/2017, 12h06	#3
djslowrnb Débutant T-E Date d'inscription: septembre 2014 Localisation: Lyon Messages: 87 Thanks: 86 Thanked 26 Times in 20 Posts Pouvoir de réputation: 10	Thanks simple i use version 7.83 how to know the good firmware fot this version depend car to dagnostic? thanks!!!

26/09/2017, 21h53	#4
Simple Membre attaché Date d'inscription: août 2014 Localisation: NA Messages: 279 Thanks: 5 Thanked 414 Times in 80 Posts Pouvoir de réputation: 20	DiagBox from version 7.66/8.02 to 8.44 has 4.3.4, but users have used other versions successfully.

01/10/2017, 20h28	#8
Simple Membre attaché Date d'inscription: août 2014 Localisation: NA Messages: 279 Thanks: 5 Thanked 414 Times in 80 Posts Pouvoir de réputation: 20	Was the VCI working with the same 308? Try using your VCI with another Peugeot or Citroen car and see if it detects it. Is the Windows Driver installing and working OK? Some VCI's have a problem with C5 and 207/208. More experienced forum members may be able to help!!

02/10/2017, 00h07	#9
djslowrnb Débutant T-E Date d'inscription: septembre 2014 Localisation: Lyon Messages: 87 Thanks: 86 Thanked 26 Times in 20 Posts Pouvoir de réputation: 10	thanks for response Simple!! I have problem when i read vin, the read fonction at random the diagnostic is not good.... i see the message connect vci.... I try to update other firmware and one time i see peripheric is not reconize but now its ok i daed my VCI?probably? regards !!