|
IMPORTANT MESSAGE FOR OUR USER |
|
|
|
Outils de la discussion | Rechercher |
20/03/2018, 21h41 | #1 |
Membre accro
Date d'inscription: juin 2013
Localisation: CHAMP
Messages: 1 003
Thanks: 496
Thanked 300 Times in 209 Posts
Pouvoir de réputation: 16 |
VCDS AIRBAG VW20 SECURITY ACCESS (golf7)
Bonjour,
je suis a la recherche du security access de vcds pour la config airbag golf 7. Merci pur votre aide |
21/03/2018, 09h56 | #2 |
Membre accro
Date d'inscription: juin 2013
Localisation: CHAMP
Messages: 1 003
Thanks: 496
Thanked 300 Times in 209 Posts
Pouvoir de réputation: 16 |
Quelqu un qui maitrise le vcds?
|
22/03/2018, 08h51 | #3 |
Membre accro
Date d'inscription: juin 2013
Localisation: CHAMP
Messages: 1 003
Thanks: 496
Thanked 300 Times in 209 Posts
Pouvoir de réputation: 16 |
personne? il sert a remettre a zero le detecteur de siege et reinitialiser les ceintures...
|
22/03/2018, 09h31 | #4 | |
Membre accro
Date d'inscription: octobre 2017
Localisation: Alger
Messages: 1 509
Thanks: 1 467
Thanked 2 864 Times in 1 066 Posts
Pouvoir de réputation: 36 |
Citation:
Essaye ce code: 30475
__________________
Il y a une nette différence entre ancienneté et expérience |
|
The Following 2 Users Say Thank You to fayssal2017 For This Useful Post: | CHATONDU38 (22/03/2018), ggvaniou (22/03/2018) |
22/03/2018, 09h42 | #5 |
Membre accro
Date d'inscription: juin 2013
Localisation: CHAMP
Messages: 1 003
Thanks: 496
Thanked 300 Times in 209 Posts
Pouvoir de réputation: 16 |
|
The Following User Says Thank You to CHATONDU38 For This Useful Post: | fayssal2017 (22/03/2018) |
22/03/2018, 09h43 | #6 |
Membre accro
Date d'inscription: octobre 2017
Localisation: Alger
Messages: 1 509
Thanks: 1 467
Thanked 2 864 Times in 1 066 Posts
Pouvoir de réputation: 36 |
Des fois le code d'accès est affiché dans l'info bull, voir la photo comme exemple
https://www.google.dz/search?num=20&...1fOW2hktBwsdM:
__________________
Il y a une nette différence entre ancienneté et expérience |
The Following 3 Users Say Thank You to fayssal2017 For This Useful Post: |
22/03/2018, 10h06 | #7 |
Membre accro
Date d'inscription: juin 2013
Localisation: CHAMP
Messages: 1 003
Thanks: 496
Thanked 300 Times in 209 Posts
Pouvoir de réputation: 16 |
ben normalement oui mais avec ma version non....j ai la 12...Et le temp que je recois la derniere la voiture sera loin....
|
The Following User Says Thank You to CHATONDU38 For This Useful Post: | fayssal2017 (22/03/2018) |
22/03/2018, 13h40 | #8 |
Membre accro
Date d'inscription: juin 2013
Localisation: CHAMP
Messages: 1 003
Thanks: 496
Thanked 300 Times in 209 Posts
Pouvoir de réputation: 16 |
je relance en esperant que quelqu un puisse m aider
|
22/03/2018, 13h47 | #9 |
TE-MANIA
Date d'inscription: janvier 2012
Localisation: maroc casablanca
Messages: 9 070
Thanks: 7 186
Thanked 14 975 Times in 6 910 Posts
Pouvoir de réputation: 172 |
salut
si tu veux faire du codage , il te faut une interface HQ , attention !!!!!!!!!! note sur un book tous les codages que tu touches !!!!!!!!! et des versions supérieur à la 12 pour une golf 7 contact GUYGUY307 il en vends , sérieux et correct (ancien membre du fofo ) cdlt |
The Following User Says Thank You to zenata For This Useful Post: | CHATONDU38 (22/03/2018) |
22/03/2018, 13h53 | #10 | |
Membre accro
Date d'inscription: juin 2013
Localisation: CHAMP
Messages: 1 003
Thanks: 496
Thanked 300 Times in 209 Posts
Pouvoir de réputation: 16 |
Citation:
C est pas pour le codage, seulement pour remetre a zero apres remplacement ceinture .... |
|
22/03/2018, 13h56 | #11 |
TE-MANIA
Date d'inscription: janvier 2012
Localisation: maroc casablanca
Messages: 9 070
Thanks: 7 186
Thanked 14 975 Times in 6 910 Posts
Pouvoir de réputation: 172 |
|
22/03/2018, 14h05 | #12 |
Membre accro
Date d'inscription: juin 2013
Localisation: CHAMP
Messages: 1 003
Thanks: 496
Thanked 300 Times in 209 Posts
Pouvoir de réputation: 16 |
C est pour ca
Seat Occupied Recognition Control Module (J706): Reset If a repair on the Seat Occupied Recognition has been performed, including the above basic settings procedure, a reset has to be performed too. Prerequisites: The Seat Occupied Recognition Control Module (J706) Basic Settings was successful. The vehicle is between 5° and 35°C (40° ~ 95°F). Battery voltage no less than 12.4 V. Passenger seat is empty and in normal position. Seatbelt must NOT be plugged in. No Component Protection, Control Module Faulty, Crash Data Stored, Control Module Not Coded or Igniter faults in the system. [Security Access - 16] Enter the Basic Settings Enabling (Seat Occupied Recognition Control Module) code shown in the pop-up balloon to enable the basic setting. [Do it!] [Basic Settings - 04] Select Resetting seat occupied recognition. When applicable type the single digit 0 into the (reserved) box. If this is not present skip this step. [Go!] to activate the Basic Setting. After the result of Finished Correctly appears click [Stop] The reset has been performed. [Done, Go Back] [Fault Codes - 02] Faults should NOT be stored [Close Controller, Go Back - 06] ---------- Post added at 15h05 ---------- Previous post was at 15h00 ---------- plutot ceci Seat Belt Tensioner Control Module Reset Prerequisites: New Seat Belt Tensioner installed Battery voltage no less than 12.4 V. Seatbelt must NOT be plugged in. No Component Protection, Control Module Faulty, Crash Data Stored, Control Module Not Coded or Igniter faults in the system. Fault such as B1304 - Left front seat belt tensioner control module: Not configured and B1305 - Right front seat belt tensioner control module: Not configured are normal prior to the matching procedure. Warning message on dash "Audi Pre Sense System Fault!" may be displayed when ignition is turned on. [Select] [15 - Airbags] [Security Access - 16] Enter the Basic Settings Enabling (Belt Tensioners) code shown in the pop-up balloon to enable the basic setting. [Do it!] [Basic Settings - 04] Select Left belt tensioner serial number -or- Right belt tensioner serial number depending on the new component(s). When applicable type the single digit 0 into the (reserved) box. If this is not present skip this step. [Go!] to activate the Basic Setting. After the result of Finished Correctly appears click [Stop] The reset has been performed. If both belts were replaced repeat for the other side at this point [Done, Go Back] [Fault Codes - 02] Faults should NOT be stored [Close Controller, Go Back - 06] |
22/03/2018, 14h16 | #13 |
Membre accro
Date d'inscription: octobre 2017
Localisation: Alger
Messages: 1 509
Thanks: 1 467
Thanked 2 864 Times in 1 066 Posts
Pouvoir de réputation: 36 |
https://www.forumgolf7.fr/forum/view...ty+access+VCDS
https://www.forumgolf7.fr/forum/viewtopic.php?t=15875
__________________
Il y a une nette différence entre ancienneté et expérience |
The Following User Says Thank You to fayssal2017 For This Useful Post: | CHATONDU38 (22/03/2018) |
22/03/2018, 14h19 | #14 |
TE-MANIA
Date d'inscription: janvier 2012
Localisation: maroc casablanca
Messages: 9 070
Thanks: 7 186
Thanked 14 975 Times in 6 910 Posts
Pouvoir de réputation: 172 |
Si une réparation de la Reconnaissance Occupée du Siège a été effectuée, y compris la procédure de configuration de base ci-dessus, une réinitialisation doit également être effectuée.
qu'est ce que tu as changé comme pièces ??? ce qui veux dire que tu as aucun défauts en mémoire je pense , il te faut une vci HQ !!!!!!!!! lorsque tu lance ton diag , le calculo airbag son numéro d'identification codage sur la première page , c'est pour ca que je te demande des captures d'écran |
22/03/2018, 14h48 | #15 |
T-E master
Date d'inscription: mai 2016
Localisation: france toulouse
Âge: 40
Messages: 2 113
Thanks: 4 157
Thanked 2 599 Times in 1 155 Posts
Pouvoir de réputation: 38 |
Salut
Toujour la lool Mais plus de vcds de dispo ---------- Post added at 03:48 PM ---------- Previous post was at 03:45 PM ---------- Je suis pas si vieux que sa zenata lool
__________________
La passion est un moteur dont personne ne mesure la puissance |
The Following User Says Thank You to guyguy307 For This Useful Post: | jah83 (24/03/2018) |
Sponsored Link |
Liens sociaux |
|
|
Discussions similaires | ||||
Discussion | Auteur | Forum | Réponses | Dernier message |
access calculateur avec clip | belghiti | Renault clip, DDT2000, Nissan consult | 3 | 03/02/2016 10h54 |
pinout airbag clio4 & golf7 Xprog | mecanodiag93 | Airbag | 0 | 07/05/2015 09h10 |
Vw20 3q0 959 655 ac | tihiuvek | Airbag | 0 | 24/11/2014 11h12 |
crash airbag vcds | nimbus | Vw, Audi, Skoda, Seat, Bentley | 4 | 30/08/2013 12h26 |
activation access multidiag | francois | Autocom, Delphi, Actia, Bosch, SPC, BrainBee, Autel | 15 | 19/01/2012 09h20 |