Tlemcen Car electronics  

Précédent   Tlemcen Car electronics > Categorie principale > Section for english users

Section for english users English talking about cars, problems and solutions ...

VF2
Réponse
 
Outils de la discussion
Vieux 29/04/2014, 15h44   #1
runsun
Membre Non Confirmé
 
Avatar de runsun
 
Date d'inscription: avril 2014
Localisation: Skien
Messages: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Pouvoir de réputation: 0
runsun is an unknown quantity at this point
Par défaut BSI - EEPROM 95160 replace/switch for C3, 2002, 1.4petrolKFV

Hi !

I hope someone can answer me at these question:

Question : Is it possible to remove the EEPROM 95160 from at partly damaged BSI and solder/mount it in a new(used) BSI and resolve the immobilizer problem.

(After browsing the web I understands that all the immobilizer data are saved in the EEPROM 95160, - but maybe are the immobilizer data stored in several places in the BSI unit, I haven't found a proper solution) ?

Thanks for your interest !

Reg. Rune S. - Norway

runsun est déconnecté   Réponse avec citation
Vieux 29/04/2014, 17h52   #2
Amine-TE
Fondateur
 
Avatar de Amine-TE
 
Date d'inscription: novembre 2008
Localisation: Offset: 0xFF25F255
Âge: 37
Messages: 120 803
Thanks: 2 666
Thanked 14 900 Times in 2 426 Posts
Pouvoir de réputation: 1319
Amine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond repute
Par défaut

On most of bsi it's possible, exept that one in 99% of case when you desolder the eprom ic it will be blank, need to recode with diag tool !

I got this many times.

Please don't forget to read rules and put an avatar and full location.
__________________
Je ne donne pas d'aide en privé.
Amine-TE est déconnecté   Réponse avec citation
Vieux 30/04/2014, 08h26   #3
runsun
Membre Non Confirmé
 
Avatar de runsun
 
Date d'inscription: avril 2014
Localisation: Skien
Messages: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Pouvoir de réputation: 0
runsun is an unknown quantity at this point
Par défaut

Thanks Fondateur, may I should give it a try ?

Anything I can do to avoid erasing the eeprom, maybe proper wire to earth ?

Reg. Rune S. - Norway
runsun est déconnecté   Réponse avec citation
Vieux 30/04/2014, 19h50   #4
Amine-TE
Fondateur
 
Avatar de Amine-TE
 
Date d'inscription: novembre 2008
Localisation: Offset: 0xFF25F255
Âge: 37
Messages: 120 803
Thanks: 2 666
Thanked 14 900 Times in 2 426 Posts
Pouvoir de réputation: 1319
Amine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond reputeAmine-TE has a reputation beyond repute
Par défaut

You have to try, no warantee anyway.
__________________
Je ne donne pas d'aide en privé.
Amine-TE est déconnecté   Réponse avec citation
Vieux 05/05/2014, 12h13   #5
runsun
Membre Non Confirmé
 
Avatar de runsun
 
Date d'inscription: avril 2014
Localisation: Skien
Messages: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Pouvoir de réputation: 0
runsun is an unknown quantity at this point
Par défaut

Hi !

Of note: I have changed eeprom95160 from a BSI(1) to another BSI(2) with the result that eeprom95160 data was deleted.
This work is NOT recommended....... :twisted:

re. Rune S. - Norway
runsun est déconnecté   Réponse avec citation
Vieux 13/05/2014, 09h29   #6
avtec
Membre Non Confirmé
 
Avatar de avtec
 
Date d'inscription: mai 2014
Localisation: Russia
Âge: 52
Messages: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Pouvoir de réputation: 0
avtec is an unknown quantity at this point
Par défaut

Citation:
Envoyé par runsun Voir le message
Hi !

Of note: I have changed eeprom95160 from a BSI(1) to another BSI(2) with the result that eeprom95160 data was deleted.
This work is NOT recommended....... :twisted:

re. Rune S. - Norway
need an access code for immobilization and any device that can register keys. Code can be obtained from the engine or vin. BSI in the dump all in FF and encoding device, old keys are stored
avtec est déconnecté   Réponse avec citation
Vieux 31/07/2014, 03h58   #7
johnnybeast
Membre Non Confirmé
 
Avatar de johnnybeast
 
Date d'inscription: juillet 2014
Localisation: Dudley, UK
Messages: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Pouvoir de réputation: 0
johnnybeast is an unknown quantity at this point
Par défaut

Hi Runsun, the only way to get it back up and running now it to flash a 'virgin' BSI file to the 95160 EEPROM the re-configure with PP2000 or Lexia.

You will need the security code tho, you can get that from the ECU, which is stored on a small EEPROM in there. You'll need to read it and pop the file into ImmoTool or similar program and get the code from that.
johnnybeast est déconnecté   Réponse avec citation
Vieux 26/01/2016, 04h27   #8
valdir
Débutant
 
Avatar de valdir
 
Date d'inscription: novembre 2008
Localisation: Passo Fundo, RS Brasil
Âge: 51
Messages: 10
Thanks: 13
Thanked 1 Time in 1 Post
Pouvoir de réputation: 0
valdir is an unknown quantity at this point
Par défaut

some cars run and some not, delete eeprom, really not a good way
valdir est déconnecté   Réponse avec citation
Sponsored Link
Réponse

Liens sociaux

Outils de la discussion

Règles de messages
Vous ne pouvez pas créer de nouvelles discussions
Vous ne pouvez pas envoyer des réponses
Vous ne pouvez pas envoyer des pièces jointes
Vous ne pouvez pas modifier vos messages

Les balises BB sont activées : oui
Les smileys sont activés : oui
La balise [IMG] est activée : oui
Le code HTML peut être employé : non

Navigation rapide

Discussions similaires
Discussion Auteur Forum Réponses Dernier message
cherche PINOUT BSI 206 eeprom 95160 beka1975 Flasheur de calculateur 1 06/12/2013 19h20
identification eeprom 95160 bsi sofiane78 Réparation & Programmation des calculateurs 5 15/02/2013 08h47
delphi eeprom 95160 autodiagnos kamal Immobilizer dumps/solutions 5 14/01/2013 10h56
clio 3 rs Eeprom 95160 S3000 powermap Immobilizer dumps/solutions 7 19/12/2012 00h50
Seeprog et eeprom 95160 benaknoun Programmeur de chip 3 09/06/2010 14h05


Fuseau horaire GMT +1. Il est actuellement 12h05.


Tlemcen-electronic.com ne tolère aucune des opérations illégales et ne prend pas en charge les responsabilités pour la perte de l'équipement utilisé.
Toutes discussion sur ce forum est à des fins expérimentales et éducatives seulement. Utilisez les informations fournis par les membres à vos propres risques.
Partenaires : Cars Review - DZSAT : Télévision Par Satellite,Médias,Fréquences,Card sharing.
- GSM-ALGERIE - [ Box & outils Gsm ] - Guide Algérie- Musique mp3 - Bled Music" - EcuServer - Immo off & virgin, airbag cleaner online - Rafplus.com le gratuit sur internet - presse algerie - OBDFR.COM, France Diag - Info Algerie - Le Portail de petites annonces en Algérie- Informastore - Boutique Informatique & Multimedia - mandataire auto - Annonces Algérie HexaShopping - ChipTuning professionnel express
Tlemcen-electronic © All right reserved