Help mon VCI ne reconnais aucuns calculateurs

[inventeur67]

Bonjour,

Voilà quelques jours que j'ai reçu mon câble de diagnostique, j'ai suivi la vidéo envoyé avec le câble pour installer diagbox v7.61. une fois l'installation terminée sur un ordi sous XP SP3 le lance diagbox puis je connecte mon VCI en 4.3.3 ( dabord à l'ordi puis au véhicule ) il reconnais mon VIN puis je lance une recherche de défauts et là il ne se connecte à aucuns calculateurs.:07:
Je déconnecte puis reconnecte mon câble et là il ne reconnais plus mon VIN donc je le rentre manuellement mais toujours rien au niveau des calculateurs.:banghead:
J'ai même flasher mon vci en 4.3.2db, désintallé puis réinstaller diagbox en 7.44 mais toujours rien :banghead::banghead::banghead:

Sur mon VCI il est indiqué 9780.z5

Pouvez-vous m'indiquer la démarche à suivre s'il vous plaît.

[inventeur67]

Y-a-t-il quelqu'un pour m'aider???
Please

[bbert90]

salut javais le meme probleme comment t a installe la version

[bbert90]

installe la version 7.02 avec virtual clone drive ou daemon tool tu fait une mise a jours avec la version 7.xx to 7.44

[inventeur67]

Oui c'est exactement ce que j'ai fait, j'ai utilisé daemon tool.
Faut-il avoir une connexion internet pour utiliser diagbox?

[bbert90]

ben pas de conexion internet ta instale PSA Interface Checker Install

[inventeur67]

Oui, dans gestionnaire de périphériques mon vci est bien reconnu :

ACTIA USB Devices
--> USB Com board evolution driver (UMDF)

Quand je lance psa interface checker, je clic sur ACTIVATE puis sur VERSION il m'indique :
APPLI_XS_Fuji_P106138A V4.3.2 @ACTIA03.01.14

Je clic sur RÉFÉRENCE et ca m'indique :
921815 C/ Inconnue

[Simple]

I tried Google translating your message in English, but I did not understand it..
Questions:
1- Are you installing Windows XP in a VirtualBox or on the computer directly?
2- Did you ensure that the Hard Drive controller type IDE?
3- If you are installing on Windows XP 32bit in VirtualBox, running on Windows 8 or 10.. No driver needs to be installed on Windows 10 or 8.
4- The ACTIA USB Devices driver should be "Multi-instance", but NOT USB Com board evolution driver (UMDF).

If your installation is on VirtualBox (Windows XP Virtual Machine off), go to Settings --> USB , you will see connected devices, and add the Lexia Device..
Start windows XP and you will see the device....

Now you may have to remove the driver from Device Manager and reinstall (Multi Instance) again.
Actia driver:
https://mega.nz/#!Nx8X2QQC!tB1i2eQCuiKNPdCdSBmnk1-6HmO0I8yznTt0gdykA_0
plug-in the Lexia interface and click on "ACTIAPnPInstaller.exe" to install the driver.
Good Luck. Simple.

[inventeur67]

I download it, I click on ACTIAPnPInstaller and I have already UMDF and not MULTI INSTANCE

[bbert90]

Mets a jours ton firmwar

[Simple]

Uninstall UMDF from device manager and click the delete box

[Simple]

You did not answer the questions in my first email, can you respond?

[inventeur67]

I use win xp 32 bites and the Hard Drive controller is type IDE ( no sata ).
How I can Uninstall UMDF from device manager and click the delete box?

[inventeur67]

Pour répondre à bbert, mon vci est en 4.3.3 c'est de ça dont tu parles?

[bbert90]

tien des mise a jours

[bbert90]

mince j avais pas vu tes en 4.3.3 c est des anciennes mais fonctionne avec moi

[inventeur67]

J'ai déjà effectué la 4.2.9db mais ça ne change rien. Comment désactiver la mise à jour automatique car j'étais en 4.3.3 et là je me retrouve de nouveau avec la 4.2.9db?

[inventeur67]

I Uninstall UMDF from device manager, now I have USB Com board evolution driver (Multi-instance) and when I connect to my car I can't do nothing ( don't recognize my VCI, Don't connects to calculators).

[soustourou]

bonsoir j'ai eu le meme problème aucun ecu de reconnu j'e n'ai deux comme ça dans le tiroirs j'attends une solution

[Simple]

@inventeur67, Your problem is not difficult, if your device is not faulty, you should be able to fix it...

But, you still did not answer all the questions I asked you... Are you using VirtualBox or VMware or installation directly on the computer?

I cannot guess what is the problem if you do not help me.. try this!

http://cartechnology.co.uk/showthread.php?tid=5157&pid=83650#pid83650

[MOUS25]

Slt
Question bete as tu essayé ton interface sur un autre vehicule?
Car la mienne ne fait pas certaine 307 hdi

[Simple]

Don't worry about the 4.3.x firmware, DiagBox will upgrade and downgrade automatically. All you need is to insert the device in the USB, then start DiagBox. The first thing it will do is to check the firmware and upload the proper firmware if needed.

Please be aware that some Lexia clones DO NOT work on Peugeot 307 and C-ziro / Ion and Citroen C5 !!! So if you can see the green LED blinking when you start DiagBox, then try it on another car to see if the problem is with the device.

In my device a 10k resistor missing and C57 capacitor were missing (Picture Lex1). Also, some devices have components missing... Lets hope yours is working..

[inventeur67]

Non malheureusement je n'ai pas d'autres véhicule que ma c4 et il n'y a personne dans mon entourage qui a peugeot ou citroën.

[inventeur67]

I'm sorry Iused Deamon Tools to install diagbox v7.02.
In my device just a 10k resistor missing and not the C57 capacitor.

[Simple]

The 10K resistor is pull-up for the CAN-BUS. I would say, you can safely solder and check if it works...

[Simple]

You did not say if you have the full set of optocouplers as shown in my second photo?
Anyway, you can try your device on a different Peugeot or Citroen to see if it works with them first.

[inventeur67]

No I can't Try it over vehicle because I have juste an old Peugeot 306.

[Simple]

Obviously you don't have the Full Chip device, I don't know if your interface works with 306/7 - C5 or not, I would advice you to try it on a different Peugeot or Citroen car first. Also, I don't know if adding the resistance would help, but you can try...

If it works with other PSA models but it still does not work with yours, even after adding the resistance, you could try adding all the missing parts. If you search the forums, you will find that some people bought the missing parts and soldered them on their boards.

Failing all that, you could sell it and buy a full chip device.

[inventeur67]

I will try this weekend on a Peugeot 307 ( 2002 ) not CAN and I will keep you informed , thank you very much for your help.
If it works, I try the resistance 10k.

[Simple]

I would advise to try on something other than 307 or C5!! these cars are reported to have a problem with some clones....

[Simple]

I have just come across a detailed (in French) hardware upgrade to the Lexia interface by devildante007 which you may with to consider.

http://www.tlemcen-electronic.com/forum/showthread.php?t=43964

[inventeur67]

Today I did a test on a Peugeot 206 and nothing, I think the cable is out of order.
I will re-contact the seller to see with him

[Simple]

This is the same as mine:

http://www.aliexpress.com/item/Factory-Direct-Price-Lexia3-Citroen-Peugeot-Code-Reader-Lexia-3-V48-PP2000-V25-Diagbox-V7-61/32320331216.html?spm=2114.01020208.3.10.2ImzMR&ws_ab_test=201526_2,201527_1_71_72_73_74_75,201409 _1

Lexia 3 Diagnostic Tool Description: (taken from the site)
1.It is compatible with Citroen cars including: C1, C2, C3, C4, C5, C6, C8, CCROSSER, NEMO, BERLINGO, JUMPY, JUMPER, AX, SAXO, BX and so on.
2.It is compatible with most Peugeot cars from 1995.
3.Diagnostics is performed via OBD-II connector (which is located near steering wheel) or via manufacturer-specific connector (only older cars, pre-2001).
4.lexia 3 Full Chip Firmware Serial Reference Number: 921815C/

[inventeur67]

This is mine:

http://www.ebay.fr/itm/PP2000-Lexia-3-V7-33-Interface-Diagnostique-Outil-Pr-Peugeot-Citroen-V7-V48-V25-/360905007723?hash=item54079d626b

I see with the seller for warranty before doing anything.

[inventeur67]

PP2000 Lexia 3 Diagnostic Interface Scan Tool For Peugeot Citroen V7 V48 V25
Brand New!!!
- Lexia 3 Interface Supplied With Diagbox V7.33 Stable Full Version,Interface works on Peugeot 307 and Citreon C5.

[Simple]

If they confirm the C5 and 307, it is good, also it has a couple of extra connectors.
Good Luck.