si vous avez été banni pour une raison de spam sur le forum (hacked account) c'est parce que votre compte a été utilisé par des Bots, merci d'envoyer un message via le formulaire de contact en bas de cette page afin de récupérer votre compte, les messages/discussions supprimés ne seront malheureusement pas restaurés.

Simple · 14/09/2015, 09h44

This morning I operated DiagBox v7.76 with the network connected to the internet and noticed a message stating that DiagBox v7.xx will be unusable after 16 October 2015, and that I will have to install DVD 8 (DiagBox 8.xx)...

Well, to verify this news I turned DiagBox off, advanced the date on my computer to October 20th 2015 and sure enough, my previously working installation gave me the error "The communication card is incorrectly initialized. The tool must be restarted". Tried a couple of times, but to no avail..

With the date still advanced, I turned off DiagBox, disconnected the network then turned DiagBox on again, and it worked. See attached photos.

The moral of the story, to avoid errors, keep your network cable/card disconnected. In fact DiagBox seem to respond faster with network disconnected.

Tests were performed on; Notebook: HP Envy M6, CPU: intel i5, Ram: 8 GB, Hard Drive: 1 TB SSHD, Operating System: Windows 10 64bit running VMware Workstation 12 on which DiagBox 7.76 is installed on Windows 10 32bit / 4 GB RAM / 40 GB Drive Virtual Machine.

14/09/2015, 10h45

It's DiagBox v7.76 of maitresox or you have a original soft??

Simple · 14/09/2015, 10h50

It seems to be looking for information when you start it. But after it starts, it runs at the same speed.
Simple..

Simple · 14/09/2015, 10h55

My installation is patched by Maitresox, but I think it is irrelevant, because the message is from PSA.

We probably need to perform further testing.

**MrRorry** · 24/09/2015, 01h15

Citation:

Envoyé par Simple

This morning I operated DiagBox v7.76 with the network connected to the internet and noticed a message stating that DiagBox v7.xx will be unusable after 16 October 2015, and that I will have to install DVD 8 (DiagBox 8.xx)...

Well, to verify this news I turned DiagBox off, advanced the date on my computer to October 20th 2015 and sure enough, my previously working installation gave me the error "The communication card is incorrectly initialized. The tool must be restarted". Tried a couple of times, but to no avail..

With the date still advanced, I turned off DiagBox, disconnected the network then turned DiagBox on again, and it worked. See attached photos.

The moral of the story, to avoid errors, keep your network cable/card disconnected. In fact DiagBox seem to respond faster with network disconnected.

Tests were performed on; Notebook: HP Envy M6, CPU: intel i5, Ram: 8 GB, Hard Drive: 1 TB SSHD, Operating System: Windows 10 64bit running VMware Workstation 12 on which DiagBox 7.76 is installed on Windows 10 32bit / 4 GB RAM / 40 GB Drive Virtual Machine.

Great job simple! i've seen that on mine too.
you maybe found the trick to keep our diagbox working after the 16/10/2015
Thanks.

**Amine-TE** · 24/09/2015, 02h21

We must get 8.XX installation cracked it's the only way, what about scarymistake, i don't follow news from him part.

Simple · 24/09/2015, 03h16

******ly, it is not necessary.... I forwarded the date on the computer where DiagBox 7.77 is installed and it still worked..
Even if PSA blocks those who try to connect, just making sure that the network cable is disconnected is good enough... I think....., only time will tell.

24/09/2015, 02h21	#6
Amine-TE Fondateur Date d'inscription: novembre 2008 Localisation: Offset: 0xFF25F255 Âge: 38 Messages: 120 938 Thanks: 2 745 Thanked 15 503 Times in 2 533 Posts Pouvoir de réputation: 1326	We must get 8.XX installation cracked it's the only way, what about scarymistake, i don't follow news from him part. __________________ Je ne donne pas d'aide en privé.

Discussions similaires
Discussion	Auteur	Forum	Réponses	Dernier message
Cartographie 2015 v1 RNEG My Way/Wip Nav – PSA + radar Mai 2015	momo92700	Autoradio et Navigateur GPS	3	16/06/2016 22h55
Lexia, diagbox... Vin Lu par diagbox mais pas de communication avec les calculateurs	julien34560	LEXIA, PP2000, DiagBox	24	13/12/2015 09h42
Etk bmw 03 2015	anasco	Logiciel & autres documentations général	3	08/07/2015 09h35
Wis 01.2015	2009mohrice	MBStar, Xentry, DAS	0	17/05/2015 13h49

14/09/2015, 10h45	#2
bouzi002 Guest Messages: n/a	It's DiagBox v7.76 of maitresox or you have a original soft??

14/09/2015, 10h50	#3
Simple Membre attaché Date d'inscription: août 2014 Localisation: NA Messages: 279 Thanks: 5 Thanked 415 Times in 80 Posts Pouvoir de réputation: 21	It seems to be looking for information when you start it. But after it starts, it runs at the same speed. Simple..

14/09/2015, 10h55	#4
Simple Membre attaché Date d'inscription: août 2014 Localisation: NA Messages: 279 Thanks: 5 Thanked 415 Times in 80 Posts Pouvoir de réputation: 21	My installation is patched by Maitresox, but I think it is irrelevant, because the message is from PSA. We probably need to perform further testing.

24/09/2015, 03h16	#7
Simple Membre attaché Date d'inscription: août 2014 Localisation: NA Messages: 279 Thanks: 5 Thanked 415 Times in 80 Posts Pouvoir de réputation: 21	******ly, it is not necessary.... I forwarded the date on the computer where DiagBox 7.77 is installed and it still worked.. Even if PSA blocks those who try to connect, just making sure that the network cable is disconnected is good enough... I think....., only time will tell.