si vous avez été banni pour une raison de spam sur le forum (hacked account) c'est parce que votre compte a été utilisé par des Bots, merci d'envoyer un message via le formulaire de contact en bas de cette page afin de récupérer votre compte, les messages/discussions supprimés ne seront malheureusement pas restaurés.

omarzoro · 15/08/2017, 14h13

Bonjour
Mon problème est que je fais une bêtise sur mon interface Diagbox Révérence 921815 /C qui marche bien ; en le flashons avec un fichier révérence 963830 /c et du-cou il naît plus reconnu!
vous n'avez pas le firmware d’origine révérence 921815 /C pour le reflasher svp ?

Simple · 19/08/2017, 07h36

I tried Google Translate but I am not sure if I understand it properly.

However, if you have a problem with the VCI NOT being recognized after flashing the firmware, it could be due to error during the flashing process. This can be due to:
1- Corrupt Firmware file. (bad file from source or during extraction (unZIP) or download)
2- Corruption in flashing process. (Low or fluctuating voltage or Anti Virus)
3- Problem with the Chip or the device hardware. (Loose connector/cable or bad component affected by cold or heat)

To see if this can be fixed do the following:

1- Download the Firmware again from a different source, like here:

use a Torrent downloader and download only the Firmware. Or from other source.

2- Use a different computer to flash the firmware, and ensure that the computer is connected to the mains (Electricity not Battery). It is possible that the computer USB voltage was at or below the threshold needed for the flashing process.
After flashing is successful, keep the VCI connected to USB for at least 10 seconds before disconnecting the device.

3- If it is bad connection or a faulty chip, then ensure that cables are plugged in properly and do not move them during the flashing process. chip replacement would be necessary, and could be more difficult to fix. I hope this is not the case.

Good luck.

---------- Post added at 07:36 AM ---------- Previous post was at 07:33 AM ----------

http://www.tlemcen-electronic.com/fo...ad.php?t=64153

omarzoro · 19/08/2017, 12h52

Thank you simple i will try

omarzoro · 24/08/2017, 17h40

Résolu merci tout le monde

Simple · 24/08/2017, 19h44

Just for all to know, it was the ACTIA Drivers on Windows that did not recognize the VCI. So a reinstall did the trick.

@omarzoro,
I told you in a post on the other forum this:
https://www.lesamisdudiag.com/diagbo...tml#post211605
Salam omarzoro,
The Firmware you installed on your VCI should work, if you can communicate with the VCI then uninstall the Drivers and reinstall them. I think it is accidental that it did not work and the problem may be in a connection.

On August 21st.. You see why sometimes we get fed up because the user does not feedback properly..

15/08/2017, 14h13	#1
omarzoro Membre accro Date d'inscription: décembre 2013 Localisation: France Messages: 1 756 Thanks: 1 719 Thanked 6 840 Times in 1 191 Posts Pouvoir de réputation: 82	Diagbox Révérence 921815 /C Bonjour Mon problème est que je fais une bêtise sur mon interface Diagbox Révérence 921815 /C qui marche bien ; en le flashons avec un fichier révérence 963830 /c et du-cou il naît plus reconnu! vous n'avez pas le firmware d’origine révérence 921815 /C pour le reflasher svp ? __________________ TELEGRAM https://t.me/OMARZORO

19/08/2017, 12h52	#3
omarzoro Membre accro Date d'inscription: décembre 2013 Localisation: France Messages: 1 756 Thanks: 1 719 Thanked 6 840 Times in 1 191 Posts Pouvoir de réputation: 82	Thank you simple i will try __________________ TELEGRAM https://t.me/OMARZORO

24/08/2017, 17h40	#4
omarzoro Membre accro Date d'inscription: décembre 2013 Localisation: France Messages: 1 756 Thanks: 1 719 Thanked 6 840 Times in 1 191 Posts Pouvoir de réputation: 82	Résolu merci tout le monde __________________ TELEGRAM https://t.me/OMARZORO

Discussions similaires
Discussion	Auteur	Forum	Réponses	Dernier message
Lexia, diagbox... Vin Lu par diagbox mais pas de communication avec les calculateurs	julien34560	LEXIA, PP2000, DiagBox	24	13/12/2015 09h42
DIAGBOX 7.34->7.35 et 7.35->7.36	fufounet	LEXIA, PP2000, DiagBox	6	23/03/2014 21h58
Diagbox	garageducentre	LEXIA, PP2000, DiagBox	13	14/03/2014 15h58
Diagbox lis que le vin	Niga	LEXIA, PP2000, DiagBox	6	13/10/2013 10h56
Révérence	Formator	Café du forum	37	23/10/2011 19h14

19/08/2017, 07h36	#2
Simple Membre attaché Date d'inscription: août 2014 Localisation: NA Messages: 279 Thanks: 5 Thanked 415 Times in 80 Posts Pouvoir de réputation: 21	I tried Google Translate but I am not sure if I understand it properly. However, if you have a problem with the VCI NOT being recognized after flashing the firmware, it could be due to error during the flashing process. This can be due to: 1- Corrupt Firmware file. (bad file from source or during extraction (unZIP) or download) 2- Corruption in flashing process. (Low or fluctuating voltage or Anti Virus) 3- Problem with the Chip or the device hardware. (Loose connector/cable or bad component affected by cold or heat) To see if this can be fixed do the following: 1- Download the Firmware again from a different source, like here: use a Torrent downloader and download only the Firmware. Or from other source. 2- Use a different computer to flash the firmware, and ensure that the computer is connected to the mains (Electricity not Battery). It is possible that the computer USB voltage was at or below the threshold needed for the flashing process. After flashing is successful, keep the VCI connected to USB for at least 10 seconds before disconnecting the device. 3- If it is bad connection or a faulty chip, then ensure that cables are plugged in properly and do not move them during the flashing process. chip replacement would be necessary, and could be more difficult to fix. I hope this is not the case. Good luck. ---------- Post added at 07:36 AM ---------- Previous post was at 07:33 AM ---------- http://www.tlemcen-electronic.com/fo...ad.php?t=64153

24/08/2017, 19h44	#5
Simple Membre attaché Date d'inscription: août 2014 Localisation: NA Messages: 279 Thanks: 5 Thanked 415 Times in 80 Posts Pouvoir de réputation: 21	Just for all to know, it was the ACTIA Drivers on Windows that did not recognize the VCI. So a reinstall did the trick. @omarzoro, I told you in a post on the other forum this: https://www.lesamisdudiag.com/diagbo...tml#post211605 Salam omarzoro, The Firmware you installed on your VCI should work, if you can communicate with the VCI then uninstall the Drivers and reinstall them. I think it is accidental that it did not work and the problem may be in a connection. On August 21st.. You see why sometimes we get fed up because the user does not feedback properly..